Your IP address will be publicly visible if you make any edits.
3DS:Bmbt3DS
Bare-metal button tester for the 3DS
More actions
Revision as of 19:40, 31 January 2024 by Doge 2(talk | contribs)(add tabber for boot9strap, fastboot3DS, ntrboot, godmode9 and luma3ds chainloader (thanks for the suggestion blue!))
BMBT3DS is a bare metal button testing .firm payload for the Nintendo 3DS. It can be used to test all buttons on the console, and to see if one is being held down or not.
The latest release of bmbt3DS (the bmbt3ds.firm file)
Section I - Running the test
Power off your console
Remove the SD card from your console and insert it into your computer
Copy bmbt3ds.firm to the root of your SD Card
Rename boot.firm to luma.firm
Rename bmbt3ds.firm to boot.firm
Safely eject the SD card from your computer and reinsert it into your console
Power on the console without pressing any buttons
This payload does not show anything on either screens until a button is pressed. Refer to the attached image for what parts of the screen will light up for each button pressed.
Press each button once, verifying that the corresponding button shows up on the top screen. If it does not show up, the button pressed may be faulty. If you see a constant white square for one button and you are not holding the button down, that button may be stuck and could be the source of some issues.
Once you are finished with the button tester, press the power button once to power off the console
Remove the SD card from your console and insert it into your computer
Delete boot.firm from the root of your SD card
Rename luma.firm to boot.firm
Safely eject the SD card from your computer and reinsert it into your console
Power on your console
If all went well, you have successfully tested the buttons on your console.
Power off your console
Remove the SD card from your console and insert it into your computer
Copy bmbt3ds.firm to the root of your SD Card
Safely eject the SD card from your computer and reinsert it into your console
Power on the console while holding HOME to enter the fastboot3DS menu
Select [+]Boot from file... -> sdmc: -> bmbt3ds.firm
This payload does not show anything on either screens until a button is pressed. Refer to the attached image for what parts of the screen will light up for each button pressed.
Press each button once, verifying that the corresponding button shows up on the top screen. If it does not show up, the button pressed may be faulty. If you see a constant white square for one button and you are not holding the button down, that button may be stuck and could be the source of some issues.
Once you are finished with the button tester, press the power button once to power off the console
Remove the SD card from your console and insert it into your computer
Delete bmbt3ds.firm from the root of your SD card
Safely eject the SD card from your computer and reinsert it into your console
Power on your console
If all went well, you have successfully tested the buttons on your console.
If you do not have a flashcart compatible with ntrboot, please choose another option.
Power off your console
Remove the SD card from your console and insert it into your computer
Copy bmbt3ds.firm to the root of your SD Card
Rename boot.firm to luma.firm
Rename bmbt3ds.firm to boot.firm
Safely eject the SD card from your computer and reinsert it into your console
Insert the flashcart flashed with ntrboot into your console
Note, 2DS users will not need a magnet, as their device cannot physically fold. Instead, move the sleep switch to the right
Press and hold START+SELECT+X, then briefly press and hold the power button for 2 to 3 seconds
Your console should now be booted into BMBT.
If it did not boot and instead booted into the HOME Menu or turned off immediately, power off your console and try again. You may need a few attempts to get the magnet positioning correct.
This payload does not show anything on either screens until a button is pressed. Refer to the attached image for what parts of the screen will light up for each button pressed.
Press each button once, verifying that the corresponding button shows up on the top screen. If it does not show up, the button pressed may be faulty. If you see a constant white square for one button and you are not holding the button down, that button may be stuck and could be the source of some issues.
Once you are finished with the button tester, press the power button once to power off the console
Remove the SD card from your console and insert it into your computer
Delete boot.firm from the root of your SD card
Rename luma.firm to boot.firm
Safely eject the SD card from your computer and reinsert it into your console
Power on your console
If all went well, you have successfully tested the buttons on your console.
This section only applies to consoles with GodMode9 installed into FIRM0/1.
Power off your console
Remove the SD card from your console and insert it into your computer
Copy bmbt3ds.firm to the sd:/gm9/payloads folder on your SD card
Reinsert the SD card into your console
Power on the console while holding R+← to enter the GodMode9 bootloader menu
Select Select payload... -> bmbt3ds.firm
This payload does not show anything on either screens until a button is pressed. Refer to the attached image for what parts of the screen will light up for each button pressed.
Press each button once, verifying that the corresponding button shows up on the top screen. If it does not show up, the button pressed may be faulty. If you see a constant white square for one button and you are not holding the button down, that button may be stuck and could be the source of some issues.
Once you are finished with the button tester, press the power button once to power off the console
If all went well, you have successfully tested the buttons on your console.
Power off your console
Remove the SD card from your console and insert it into your computer
Copy bmbt3ds.firm to the sd:/luma/payloads folder on your SD card
Reinsert the SD card into your console
Power on the console while holding START to open Luma3DS chainloader
If you still don't see it, follow the boot9strap tab above instead
Select bmbt3ds.firm
This payload does not show anything on either screens until a button is pressed. Refer to the attached image for what parts of the screen will light up for each button pressed.
Press each button once, verifying that the corresponding button shows up on the top screen. If it does not show up, the button pressed may be faulty. If you see a constant white square for one button and you are not holding the button down, that button may be stuck and could be the source of some issues.
Once you are finished with the button tester, press the power button once to power off the console
If all went well, you have successfully tested the buttons on your console.