Tags: New redirect Reverted |
Tags: Removed redirect Undo |
| Line 1: |
Line 1: |
| #REDIRECT [[3DS:Bmbt3DS]]
| | {{Infobox homebrew |
| | | for3ds = 1 |
| | | forwiiu = 0 |
| | | forswitch = 0 |
| | | forwii = 0 |
| | | developers = Gruetzig |
| | | version = bmbt3DS +1 |
| | | releasedate = 2023-06-07 |
| | | github = Gruetzig/bmbt3ds |
| | | forwindows = 0 |
| | | formac = 0 |
| | | forlinux = 0 |
| | | forjava = 0 |
| | }} |
| | |
| | BMBT3DS is a bare metal button testing <code>.firm</code> payload for the Nintendo 3DS. It can be used to test all buttons on the console, and to see if one is being held down or not. |
| | |
| | ==Instructions== |
| | |
| | ===What you will need=== |
| | |
| | *[[3DS:Boot9strap|boot9strap]], [[3DS:GodMode9|GodMode9]] or [[3DS:Fastboot3DS|fastboot3DS]] installed to the FIRM partition(s) |
| | *[[3DS:Luma3DS|Luma3DS]]' <code>boot.firm</code> on the root of your SD card |
| | *The latest release of [https://github.com/Gruetzig/bmbt3ds/releases/latest bmbt3DS] (the <code>bmbt3ds.firm</code> file) |
| | |
| | ===Section I - Running the test=== |
| | <tabber> |
| | |-|boot9strap= |
| | |
| | <ol> |
| | <li> Power off your console </li> |
| | <li> Remove the SD card from your console and insert it into your computer </li> |
| | <li> Copy <code>bmbt3ds.firm</code> to the root of your SD Card </li> |
| | <li> Rename <code>boot.firm</code> to <code>luma.firm</code> </li> |
| | <li> Rename <code>bmbt3ds.firm</code> to <code>boot.firm</code> </li> |
| | <li> Safely eject the SD card from your computer and reinsert it into your console </li> |
| | <li> Power on the console without pressing any buttons <br>{{Info|text=This payload does not show anything on either screens until a button is pressed. Refer to the attached image for what parts of the screen will light up for each button pressed.|image=[[File:Bmbt.png|384px]]}} </li> |
| | <li> Press each button once, verifying that the corresponding button shows up on the top screen. If it does not show up, the button pressed may be faulty. If you see a constant white square for one button and you are '''not''' holding the button down, that button may be stuck and could be the source of some issues. </li> |
| | <li> Once you are finished with the button tester, press the power button once to power off the console </li> |
| | <li> Remove the SD card from your console and insert it into your computer </li> |
| | <li> Delete <code>boot.firm</code> from the root of your SD card </li> |
| | <li> Rename <code>luma.firm</code> to <code>boot.firm</code> </li> |
| | <li> Safely eject the SD card from your computer and reinsert it into your console </li> |
| | <li> Power on your console </li> |
| | </ol> |
| | {{Success|text=If all went well, you have successfully tested the buttons on your console.}} |
| | |
| | |-|fastboot3DS= |
| | |
| | <ol> |
| | <li> Power off your console </li> |
| | <li> Remove the SD card from your console and insert it into your computer </li> |
| | <li> Copy <code>bmbt3ds.firm</code> to the root of your SD Card </li> |
| | <li> Safely eject the SD card from your computer and reinsert it into your console </li> |
| | <li> Power on the console while holding {{B|HOME}} to enter the fastboot3DS menu </li> |
| | <li> Select <code>[+]Boot from file...</code> -> <code>sdmc:</code> -> <code>bmbt3ds.firm</code> <br>{{Info|text=This payload does not show anything on either screens until a button is pressed. Refer to the attached image for what parts of the screen will light up for each button pressed.|image=[[File:Bmbt.png|384px]]}} </li> |
| | <li> Press each button once, verifying that the corresponding button shows up on the top screen. If it does not show up, the button pressed may be faulty. If you see a constant white square for one button and you are '''not''' holding the button down, that button may be stuck and could be the source of some issues. </li> |
| | <li> Once you are finished with the button tester, press the power button once to power off the console </li> |
| | <li> Remove the SD card from your console and insert it into your computer </li> |
| | <li> Delete <code>bmbt3ds.firm</code> from the root of your SD card </li> |
| | <li> Safely eject the SD card from your computer and reinsert it into your console </li> |
| | <li> Power on your console </li> |
| | </ol> |
| | {{Success|text=If all went well, you have successfully tested the buttons on your console.}} |
| | |
| | |-|ntrboot= |
| | {{warning|text=If you do not have a flashcart compatible with ntrboot, please choose another option.}} |
| | <ol> |
| | <li> Power off your console </li> |
| | <li> Remove the SD card from your console and insert it into your computer </li> |
| | <li> Copy <code>bmbt3ds.firm</code> to the root of your SD Card </li> |
| | <li> Rename <code>boot.firm</code> to <code>luma.firm</code> </li> |
| | <li> Rename <code>bmbt3ds.firm</code> to <code>boot.firm</code> </li> |
| | <li> Safely eject the SD card from your computer and reinsert it into your console </li> |
| | <li> Insert the flashcart flashed with ntrboot into your console </li> |
| | <li> Put the magnet into position to trigger the lid sensor. Refer to [https://i.imgur.com/5e3lKe2.png this image for reference] |
| | <ul><li>Note, 2DS users will not need a magnet, as their device cannot physically fold. Instead, move the sleep switch to the right</li></ul> |
| | </li> |
| | <li> Press and hold {{Key press|START|SELECT|X}}, then briefly press and hold the power button for 2 to 3 seconds </li> |
| | <li> Your console should now be booted into BMBT. |
| | <ul><li> If it did not boot and instead booted into the HOME Menu or turned off immediately, power off your console and try again. You may need a few attempts to get the magnet positioning correct.</li></ul> |
| | {{Info|text=This payload does not show anything on either screens until a button is pressed. Refer to the attached image for what parts of the screen will light up for each button pressed.|image=[[File:Bmbt.png|384px]]}}</li> |
| | <li> Press each button once, verifying that the corresponding button shows up on the top screen. If it does not show up, the button pressed may be faulty. If you see a constant white square for one button and you are '''not''' holding the button down, that button may be stuck and could be the source of some issues. </li> |
| | <li> Once you are finished with the button tester, press the power button once to power off the console </li> |
| | <li> Remove the SD card from your console and insert it into your computer </li> |
| | <li> Delete <code>boot.firm</code> from the root of your SD card </li> |
| | <li> Rename <code>luma.firm</code> to <code>boot.firm</code> </li> |
| | <li> Safely eject the SD card from your computer and reinsert it into your console </li> |
| | <li> Power on your console </li> |
| | </ol> |
| | {{Success|text=If all went well, you have successfully tested the buttons on your console.}} |
| | |
| | |-|GodMode9= |
| | |
| | {{warning|text=This section only applies to consoles with GodMode9 installed into FIRM0/1.}} |
| | <ol> |
| | <li> Power off your console </li> |
| | <li> Remove the SD card from your console and insert it into your computer </li> |
| | <li> Copy <code>bmbt3ds.firm</code> to the <code>sd:/gm9/payloads</code> folder on your SD card </li> |
| | <li> Reinsert the SD card into your console </li> |
| | <li> Power on the console while holding {{Key press|R|LEFT}} to enter the GodMode9 bootloader menu </li> |
| | <li> Select <code>Select payload...</code> -> <code>bmbt3ds.firm</code> <br>{{Info|text=This payload does not show anything on either screens until a button is pressed. Refer to the attached image for what parts of the screen will light up for each button pressed.|image=[[File:Bmbt.png|384px]]}} </li> |
| | <li> Press each button once, verifying that the corresponding button shows up on the top screen. If it does not show up, the button pressed may be faulty. If you see a constant white square for one button and you are '''not''' holding the button down, that button may be stuck and could be the source of some issues. </li> |
| | <li> Once you are finished with the button tester, press the power button once to power off the console </li> |
| | </ol> |
| | {{Success|text=If all went well, you have successfully tested the buttons on your console.}} |
| | |
| | |-|Luma3DS chainloader= |
| | |
| | <ol> |
| | <li> Power off your console </li> |
| | <li> Remove the SD card from your console and insert it into your computer </li> |
| | <li> Copy <code>bmbt3ds.firm</code> to the <code>sd:/luma/payloads</code> folder on your SD card </li> |
| | <li> Reinsert the SD card into your console </li> |
| | <li> Power on the console while holding {{B|START}} to open Luma3DS chainloader |
| | <ul> |
| | <li> If you dont see Luma3DS chainloader, follow [[3dsguide:restoring-updating-cfw.html|Restoring / Updating CFW]] and try again </li> |
| | <li> If you still don't see it, follow the boot9strap tab above instead </li> |
| | </ul></li> |
| | <li> Select <code>bmbt3ds.firm</code> <br>{{Info|text=This payload does not show anything on either screens until a button is pressed. Refer to the attached image for what parts of the screen will light up for each button pressed.|image=[[File:Bmbt.png|384px]]}} </li> |
| | <li> Press each button once, verifying that the corresponding button shows up on the top screen. If it does not show up, the button pressed may be faulty. If you see a constant white square for one button and you are '''not''' holding the button down, that button may be stuck and could be the source of some issues. </li> |
| | <li> Once you are finished with the button tester, press the power button once to power off the console </li> |
| | </ol> |
| | {{Success|text=If all went well, you have successfully tested the buttons on your console.}} |
| | |
| | </tabber> |
| | {{Short description|Bare-metal button tester for the 3DS}} |
