3DS:Wireless streaming: Difference between revisions

Latest revision as of 23:16, 23 October 2024

3DS:STREAM

This guide cannot be used to stream DS games, DSiWare, and GBA games. You will need a hardware capture card to do that.

This guide only works on New 3DS models.
If you have a Old 3DS model, you can use HzMod instead; however, keep in mind that Old 3DS models have very weak hardware, and extremely low framerates are unavoidable. It is generally not practical to stream with an Old 3DS.

This page will show you how to stream your New 3DS console's screens to your computer over WiFi. However, note the following things:

Your console and your computer need to be on the same network.
Streaming audio over WiFi currently isn't possible - you will need to use an AUX cable and a device with Line In at the same time to receive audio.
If you have a poor connection, you may not get the best results. The receiving computer should be connected to the network via Ethernet or a 5GHz WiFi connection.

Significantly improved performance is available through ntr-hr, a fork of the original NTR. However, it is slightly more unstable and still actively being developed.
If you do not consider that a problem, then to use ntr-hr, download BootNTRSelector-PabloMK7-Banner.cia from the ntr-hr releases page and use it in place of the BootNTR Selector .cia that would have been downloaded below.

Finding your Console's IP

You'll need to know the local IP address of your 3DS later, so it's a good idea to find it now.

Start the Homebrew Launcher
Press Y

Launch FBI
Select "Remote Install"
Select "Receive URLs over the network"

Open Rosalina with Left Shoulder+↓+Select
Select "Debugger options..."
Select "Enable debugger"
Press B to continue
Find the IP address in the top right corner
Recommended: Select "Disable debugger"

Streaming with NTR

What You Need

Your console's IP from the first section
The latest release of Snickerstream
The latest release of Luma3DS
The latest release of BootNTR Selector
FBI installed on your console

Section I: Prep Work

Ensure that your console and your computer are on the same network
Download and extract the latest Snickerstream .zip file
Download the latest Luma3DS boot.firm file
Download the latest BootNTR Selector .cia file
Power off your console
Take the SD card out of your console and put it into your computer
Replace the boot.firm file on the root of your SD card with the one you just downloaded
Copy the BootNTR selector .cia file to your SD card
- You may put this file where you can easily access it
Put your SD card back into your console

Section II: Installing CIAs

Power on your console
- If you are prompted with a Luma3DS configuration screen, just press START
Open FBI
Press A on SD at the top of your bottom screen
Find the BootNTR Selector .cia file that you copied, press A on it and select Install and delete CIA
Press START to exit FBI

Section III: Streaming

Open the Snickerstream .exe file from where you extracted it
On your console, open the gift that appeared on your home menu and launch BootNTR Selector
- If you're prompted with 3 buttons on your bottom screen, tap "Use default"
- If you're prompted to choose an NTR version, choose 3.6
- Your console's screen should flash some colors, meaning that it's ready for streaming
Input your console's IP from the first section into the IP box in the Snickerstream window
- You may also adjust your settings to your liking if you wish
Click Connect! in the Snickerstream window
- Your console's screens should now be streamed to your computer

What You Need

Your console's IP from the first section
The latest release of cuteNTR-OSX
The latest release of Luma3DS
The latest release of BootNTR Selector
FBI installed on your console

Section I: Prep Work

Ensure that your console and your computer are on the same network
Download cuteNTR-0.3.2.dmg
Download the latest Luma3DS boot.firm file
Download the latest BootNTR Selector .cia file
Power off your console
Take the SD card out of your console and put it into your computer
Replace the boot.firm file on the root of your SD card with the one you just downloaded
Copy the BootNTR selector .cia file to your SD card
- You may put this file where you can easily access it
Put your SD card back into your console

Section II: Installing CIAs

Power on your console
- If you are prompted with a Luma3DS configuration screen, just press START
Open FBI
Press A on SD at the top of your bottom screen
Find the BootNTR Selector .cia file that you copied, press A on it and select Install and delete CIA
Press START to exit FBI

Section III: Streaming

On your console, open the gift that appeared on your home menu and launch BootNTR Selector
- If you're prompted with 3 buttons on your bottom screen, tap "Use default"
- If you're prompted to choose an NTR version, choose 3.6
- Your console's screen should flash some colors, meaning that it's ready for streaming
Open the cuteNTR .dmg, and copy the app to the Applications folder
- You may be prompted to enter the admin password
Right click on the app and click 'open'
- You may be prompted to enter the admin password
Input your console's IP from the first section into the IP box in the cuteNTR window
Click Connect! in the cuteNTR window
- Your console's screens should now be streamed to your computer. The top and bottom screens will be 2 different windows. If you cannot find them, on the bottom of the screen where the dock is located, right click the cuteNTR icon and select "Show All Windows"

What You Need

Your console's IP from the first section
sudo
The latest release of Luma3DS
The latest release of BootNTR Selector
FBI installed on your console

Section I: Prep Work

Ensure that your console and your computer are on the same network
Download the latest Luma3DS boot.firm file
Download the latest BootNTR Selector .cia file
Power off your console
Take the SD card out of your console and put it into your computer
Replace the boot.firm file on the root of your SD card with the one you just downloaded
Copy the BootNTR selector .cia file to your SD card
- You may put this file where you can easily access it
Put your SD card back into your console

Section II: installing cuteNTR

This section will add a PPA to your sources in order to install cuteNTR. Proceed on your own risk.

Open the terminal
Run sudo add-apt-repository ppa:joenosie/3ds to add the PPA to your sources
Run sudo apt update && sudo apt upgrade to update your setup
Run sudo apt install cutentr to install cuteNTR

Section III: Installing CIAs

Power on your console
- If you are prompted with a Luma3DS configuration screen, just press START
Open FBI
Press A on SD at the top of your bottom screen
Find the BootNTR Selector .cia file that you copied, press A on it and select Install and delete CIA
Press START to exit FBI

Section IV: Streaming

Launch cuteNTR, either from your window manager or with cutentr in the terminal
On your console, open the gift that appeared on your home menu and launch BootNTR Selector
- If you're prompted with 3 buttons on your bottom screen, tap "Use default"
- If you're prompted to choose an NTR version, choose 3.6
- Your console's screen should flash some colors, meaning that it's ready for streaming
Input your console's IP from the first section into the IP box next to the Stream button
Click Stream in the cuteNTR window
- Your console's screens should now be streamed to your computer

What You Need

Your console's IP from the first section
sudo
The latest release of Luma3DS
The latest release of BootNTR Selector
FBI installed on your console

Section I: Prep Work

Ensure that your console and your computer are on the same network
Download the latest Luma3DS boot.firm file
Download the latest BootNTR Selector .cia file
Power off your console
Take the SD card out of your console and put it into your computer
Replace the boot.firm file on the root of your SD card with the one you just downloaded
Copy the BootNTR selector .cia file to your SD card
- You may put this file where you can easily access it
Put your SD card back into your console

Section II: Installing cuteNTR

This is a small tutorial for installing the popular AUR helper yay and installing cuteNTR with it. If you already have a working AUR helper, or know how to install AUR packages in general, you can download and make cutentr-git yourself, then continue with the next section.

Open the terminal
Run sudo pacman -S --needed git base-devel to make sure that you have the base-devel package group and git installed
- Confirm your password if prompted
Run git clone https://aur.archlinux.org/yay.git
Run cd yay
Run makepkg -si to install yay
- Confirm your password if prompted
Run yay -S cutentr-git to install cuteNTR
- Confirm your password if prompted

Section III: Installing CIAs

Power on your console
- If you are prompted with a Luma3DS configuration screen, just press START
Open FBI
Press A on SD at the top of your bottom screen
Find the BootNTR Selector .cia file that you copied, press A on it and select Install and delete CIA
Press START to exit FBI

Section IV: Streaming

Launch cuteNTR, either from your window manager or with cutentr in the terminal
On your console, open the gift that appeared on your home menu and launch BootNTR Selector
- If you're prompted with 3 buttons on your bottom screen, tap "Use default"
- If you're prompted to choose an NTR version, choose 3.6
- Your console's screen should flash some colors, meaning that it's ready for streaming
Input your console's IP from the first section into the IP box next to the Stream button
Click Stream in the cuteNTR window
- Your console's screens should now be streamed to your computer

What You Need

Your console's IP from the first section
The latest release of flatpak installed on your computer for your operating system
The latest release of Luma3DS
The latest release of BootNTR Selector
FBI installed on your console

Section I: Prep Work

Ensure that your console and your computer are on the same network
Download the latest Luma3DS boot.firm file
Download the latest BootNTR Selector .cia file
Power off your console
Take the SD card out of your console and put it into your computer
Replace the boot.firm file on the root of your SD card with the one you just downloaded
Copy the BootNTR selector .cia file to your SD card
- You may put this file where you can easily access it
Put your SD card back into your console

Section II: Installing cuteNTR

Open the terminal
Run mkdir cuteNTR && cd cuteNTR to make a new directory and go into it
Run wget https://gitlab.com/BoltsJ/cuteNTR/uploads/da6b5bafbab68b45cc9bee0ae590a3ca/com.gitlab.BoltsJ.cuteNTR.flatpak
Run flatpak install com.gitlab.BoltsJ.cuteNTR.flatpak to install cuteNTR
Confirm your password and all other prompts with yes
Run cd .. && rm -r cuteNTR to delete the directory

Section III: Installing CIAs

Power on your console
- If you are prompted with a Luma3DS configuration screen, just press START
Open FBI
Press A on SD at the top of your bottom screen
Find the BootNTR Selector .cia file that you copied, press A on it and select Install and delete CIA
Press START to exit FBI

Section IV: Streaming

Launch cuteNTR by running flatpak run com.gitlab.BoltsJ.cuteNTR
On your console, open the gift that appeared on your home menu and launch BootNTR Selector
- If you're prompted with 3 buttons on your bottom screen, tap "Use default"
- If you're prompted to choose an NTR version, choose 3.6
- Your console's screen should flash some colors, meaning that it's ready for streaming
Input your console's IP from the first section into the IP box next to the Stream button
Click Stream in the cuteNTR window
- Your console's screens should now be streamed to your computer

Using Line In to Receive Audio

What You Need

A 3.5mm to 3.5mm audio cable
An audio in (line in or microphone in) port on your computer
- Some computers have a single "headphone" port that can be used for both audio output and input. To use one of these, you will need a Y splitter cable

How to use

Connect your 3DS to your computer's audio input port with a 3.5mm to 3.5mm audio cable
Pipe the audio from your audio input port into the software you intend to use
- The exact steps will depend on the software you're using
- If you are recording or streaming your game using OBS, add a new Audio Input Capture
- If you are streaming your game via a service such as Discord, you will need to use software such as Voicemeeter to mix your microphone and 3DS audio inputs together
  - If you do not wish to speak while streaming, simply point the app at the 3DS's audio device
  - If you do not wish to mix your microphone and 3DS audio inputs together, you can set up a scene using OBS, create a Windowed Projector Preview and share on Discord that window. Then, in Advanced Audio Properties, turn on the Audio Monitoring for the 3DS Audio Input Capture so that viewers on Discord can hear the 3DS audio. Note that this last step will direct the 3DS audio also to your audio output device (headphones/speakers).
- To simply listen to the audio, you can listen to the audio input device in Windows

Troubleshooting

Games such as those in the Pokemon series, Smash Bros 3DS and many more may crash when trying to load or after a loading screen. To avoid this issue, ensure that the debugger is enabled. To do this see this page.
Similarly, such of the above games may disable Wi-Fi connection while using Snickerstream when trying to play online. To counter this, make sure to enable NFC Patch in Snickerstream.

@@ Line 1: / Line 1: @@
 {{shortcut|3DS:STREAM}}
-{{Page WIP}}
+{{warning|text=This guide cannot be used to stream DS games, DSiWare, and GBA games. You will need a hardware capture card to do that.}}
-{{Warning|text=The guides below can't be used to stream DS games, DSiWare, and GBA games. You will need a hardware capture card to do that.}}
+{{critical|text='''This guide only works on New 3DS models.'''
-{{Critical|text='''This only works for New 3DS.''' If you absolutely want a method for Old 3DS, there is [[/HzMod|HzMod]]. Keep in mind that performance is still very bad and it is not intended for practical use.}}
+<br>If you have a Old 3DS model, you can use [[/HzMod|HzMod]] instead; however, keep in mind that Old 3DS models have very weak hardware, and extremely low framerates are unavoidable. It is generally not practical to stream with an Old 3DS.}}
-This page will show you how to stream your New 3DS console's screens to your computer over WiFi.
+This page will show you how to stream your New 3DS console's screens to your computer over WiFi. However, note the following things:
-*Your console and your computer need to be on the same network.
+* Your console and your computer need to be on the same network.
-*Streaming audio over WiFi currently isn't possible, you will need to use an AUX cable and a device with Line In to receive audio.
+* Streaming audio over WiFi currently isn't possible - you will need to use an AUX cable and a device with Line In at the same time to receive audio.
-*If you have a poor connection, you may not get the best results. The receiving computer should be connected to the network via ethernet or a 5 GHz connection.
+* If you have a poor connection, you may not get the best results. The receiving computer should be connected to the network via Ethernet or a 5GHz WiFi connection.
-{{Info|text=Improved performance is available through [https://github.com/xzn/ntr-hr/releases this fork of NTR]. See the [https://gbatemp.net/threads/rel-improved-hopefully-ntr-streamer-for-n3ds-xl-ll.644726/ release thread] for more details.}}
+{{info|text=Significantly improved performance is available through [https://gbatemp.net/threads/rel-improved-hopefully-ntr-streamer-for-n3ds-xl-ll.644726/ ntr-hr], a fork of the original NTR. However, it is slightly more unstable and still actively being developed.<br>
+If you do not consider that a problem, then to use ntr-hr, download <code>BootNTRSelector-PabloMK7-Banner.cia</code> from the {{GitHub|xzn/ntr-hr/releases|ntr-hr releases page}} and use it in place of the BootNTR Selector <code>.cia</code> that would have been downloaded below.}}
-==Finding your Console's IP ==
+== Finding your Console's IP ==
 You'll need to know the local IP address of your 3DS later, so it's a good idea to find it now.
 {{3DS:Check local IP address}}
-==Streaming with NTR==
+== Streaming with NTR ==
 <tabber>
 |-|Windows - Snickerstream=
-===What You Need===
+=== What You Need ===
-*Your console's IP from the first section
+* Your console's IP from the first section
-*The latest release of [https://github.com/RattletraPM/Snickerstream/releases/latest Snickerstream]
+* The latest release of {{GitHub|RattletraPM/Snickerstream/releases/latest|Snickerstream}}
-*The latest release of [https://github.com/LumaTeam/Luma3DS/releases/latest Luma3DS]
+* The latest release of {{GitHub|LumaTeam/Luma3DS/releases/latest|Luma3DS}}
-*The latest release of [https://github.com/Nanquitas/BootNTR/releases/latest BootNTR Selector]
+* The latest release of {{GitHub|Nanquitas/BootNTR/releases/latest|BootNTR Selector}}
-*[https://github.com/lifehackerhansol/FBI/releases/latest FBI] installed on your console
+* {{GitHub|lifehackerhansol/FBI/releases/latest|FBI}} installed on your console
-=== Section I: Prep Work===
+=== Section I: Prep Work ===
 #Ensure that your console and your computer are on the same network
 # Download and extract the latest Snickerstream <code>.zip</code> file
 # Download the latest Luma3DS <code>boot.firm</code> file
 # Download the latest BootNTR Selector <code>.cia</code> file
-#Power off your console
+# Power off your console
 # Take the SD card out of your console and put it into your computer
-#Replace the <code>boot.firm</code> file on the root of your SD card with the one you just downloaded
+# Replace the <code>boot.firm</code> file on the root of your SD card with the one you just downloaded
 # Copy the BootNTR selector <code>.cia</code> file to your SD card
-#*You may put this file where you can easily access it
+#* You may put this file where you can easily access it
 # Put your SD card back into your console
-===Section II: Installing CIAs===
+=== Section II: Installing CIAs ===
 # Power on your console
-#*If you are prompted with a Luma3DS configuration screen, just press <code>START</code>
+#* If you are prompted with a Luma3DS configuration screen, just press {{B|START}}
-#Open FBI
+# Open FBI
-# Press A on <code>SD</code> at the top of your bottom screen
+# Press {{B|A}} on <code>SD</code> at the top of your bottom screen
 # Find the BootNTR Selector <code>.cia</code> file that you copied, press A on it and select <code>Install and delete CIA</code>
-#Press START to exit FBI
+# Press {{B|START}} to exit FBI
 ===Section III: Streaming===
 # Open the Snickerstream <code>.exe</code> file from where you extracted it
-#On your console, open the gift that appeared on your home menu and launch BootNTR Selector
+# On your console, open the gift that appeared on your home menu and launch BootNTR Selector
-#*If you're prompted with 3 buttons on your bottom screen, tap "Use default"
+#* If you're prompted with 3 buttons on your bottom screen, tap "Use default"
-#*If you're prompted to choose an NTR version, choose 3.6
+#* If you're prompted to choose an NTR version, choose 3.6
-#*Your console's screen should flash some colors, meaning that it's ready for streaming
+#* Your console's screen should flash some colors, meaning that it's ready for streaming
-#Input your console's IP from the first section into the IP box in the Snickerstream window
+# Input your console's IP from the first section into the IP box in the Snickerstream window
-#*You may also [https://github.com/RattletraPM/Snickerstream/wiki/Settings-101 adjust your settings] to your liking if you wish
+#* You may also {{GitHub|RattletraPM/Snickerstream/wiki/Settings-101|adjust your settings}} to your liking if you wish
-#Click <code>Connect!</code> in the Snickerstream window
+# Click <code>Connect!</code> in the Snickerstream window
-#*Your console's screens should now be streamed to your computer
+#* Your console's screens should now be streamed to your computer
 |-|macOS - cuteNTR-OSX=
-===What You Need===
+=== What You Need ===
-*Your console's IP from the first section
+* Your console's IP from the first section
-*The latest release of [https://github.com/EBLeifEricson/cuteNTR-OSX/releases/tag/0.3.2 cuteNTR-OSX]
+* The latest release of {{GitHub|EBLeifEricson/cuteNTR-OSX/releases/tag/0.3.2|cuteNTR-OSX}}
-*The latest release of [https://github.com/LumaTeam/Luma3DS/releases/latest Luma3DS]
+* The latest release of {{GitHub|LumaTeam/Luma3DS/releases/latest|Luma3DS}}
-*The latest release of [https://github.com/Nanquitas/BootNTR/releases/latest BootNTR Selector]
+* The latest release of {{GitHub|Nanquitas/BootNTR/releases/latest|BootNTR Selector}}
-*[https://github.com/lifehackerhansol/FBI/releases/latest FBI] installed on your console
+* {{GitHub|lifehackerhansol/FBI/releases/latest|FBI}} installed on your console
-=== Section I: Prep Work===
+=== Section I: Prep Work ===
 #Ensure that your console and your computer are on the same network
 # Download <code>cuteNTR-0.3.2.dmg</code>
 # Download the latest Luma3DS <code>boot.firm</code> file
 # Download the latest BootNTR Selector <code>.cia</code> file
-#Power off your console
+# Power off your console
 # Take the SD card out of your console and put it into your computer
-#Replace the <code>boot.firm</code> file on the root of your SD card with the one you just downloaded
+# Replace the <code>boot.firm</code> file on the root of your SD card with the one you just downloaded
 # Copy the BootNTR selector <code>.cia</code> file to your SD card
-#*You may put this file where you can easily access it
+#* You may put this file where you can easily access it
 # Put your SD card back into your console
-===Section II: Installing CIAs===
+=== Section II: Installing CIAs ===
 # Power on your console
-#*If you are prompted with a Luma3DS configuration screen, just press START
+#* If you are prompted with a Luma3DS configuration screen, just press {{B|START}}
-#Open FBI
+# Open FBI
-# Press A on <code>SD</code> at the top of your bottom screen
+# Press {{B|A}} on <code>SD</code> at the top of your bottom screen
 # Find the BootNTR Selector <code>.cia</code> file that you copied, press A on it and select <code>Install and delete CIA</code>
-#Press START to exit FBI
+# Press {{B|START}} to exit FBI
-===Section III: Streaming===
+=== Section III: Streaming ===
-#On your console, open the gift that appeared on your home menu and launch BootNTR Selector
+# On your console, open the gift that appeared on your home menu and launch BootNTR Selector
-#*If you're prompted with 3 buttons on your bottom screen, tap "Use default"
+#* If you're prompted with 3 buttons on your bottom screen, tap "Use default"
-#*If you're prompted to choose an NTR version, choose 3.6
+#* If you're prompted to choose an NTR version, choose 3.6
-#*Your console's screen should flash some colors, meaning that it's ready for streaming
+#* Your console's screen should flash some colors, meaning that it's ready for streaming
 # Open the cuteNTR <code>.dmg</code>, and copy the app to the Applications folder
 #* You may be prompted to enter the admin password
 # Right click on the app and click 'open'
 #* You may be prompted to enter the admin password
-#Input your console's IP from the first section into the IP box in the cuteNTR window
+# Input your console's IP from the first section into the IP box in the cuteNTR window
-#Click <code>Connect!</code> in the cuteNTR window
+# Click <code>Connect!</code> in the cuteNTR window
-#*Your console's screens should now be streamed to your computer. The top and bottom screens will be 2 different windows. If you cannot find them, on the bottom of the screen where the dock is located, right click the cuteNTR icon and select "Show All Windows"
+#* Your console's screens should now be streamed to your computer. The top and bottom screens will be 2 different windows. If you cannot find them, on the bottom of the screen where the dock is located, right click the cuteNTR icon and select "Show All Windows"
 |-|Debian Linux - cuteNTR=
-===What You Need===
+=== What You Need ===
-*Your console's IP from the first section
+* Your console's IP from the first section
-*sudo
+* sudo
-*The latest release of [https://github.com/LumaTeam/Luma3DS/releases/latest Luma3DS]
+* The latest release of {{GitHub|LumaTeam/Luma3DS/releases/latest|Luma3DS}}
-*The latest release of [https://github.com/Nanquitas/BootNTR/releases/latest BootNTR Selector]
+* The latest release of {{GitHub|Nanquitas/BootNTR/releases/latest|BootNTR Selector}}
-*[https://github.com/lifehackerhansol/FBI/releases/latest FBI] installed on your console
+* {{GitHub|lifehackerhansol/FBI/releases/latest|FBI}} installed on your console
-=== Section I: Prep Work===
-#Ensure that your console and your computer are on the same network
+=== Section I: Prep Work ===
+# Ensure that your console and your computer are on the same network
 # Download the latest Luma3DS <code>boot.firm</code> file
 # Download the latest BootNTR Selector <code>.cia</code> file
-#Power off your console
+# Power off your console
 # Take the SD card out of your console and put it into your computer
-#Replace the <code>boot.firm</code> file on the root of your SD card with the one you just downloaded
+# Replace the <code>boot.firm</code> file on the root of your SD card with the one you just downloaded
 # Copy the BootNTR selector <code>.cia</code> file to your SD card
-#*You may put this file where you can easily access it
+#* You may put this file where you can easily access it
 # Put your SD card back into your console
-=== Section II: installing cuteNTR===
+=== Section II: installing cuteNTR ===
 This section will add a [https://askubuntu.com/a/4990 PPA] to your sources in order to install cuteNTR. Proceed on your own risk.
 # Open the terminal
@@ Line 123: / Line 125: @@
 # Run <code>sudo apt install cutentr</code> to install cuteNTR
-===Section III: Installing CIAs===
+===Section III: Installing CIAs ===
 # Power on your console
-#*If you are prompted with a Luma3DS configuration screen, just press START
+#* If you are prompted with a Luma3DS configuration screen, just press {{B|START}}
-#Open FBI
+# Open FBI
-# Press A on <code>SD</code> at the top of your bottom screen
+# Press {{B|A}} on <code>SD</code> at the top of your bottom screen
 # Find the BootNTR Selector <code>.cia</code> file that you copied, press A on it and select <code>Install and delete CIA</code>
-#Press START to exit FBI
+# Press {{B|START}} to exit FBI
-===Section IV: Streaming===
+=== Section IV: Streaming ===
 # Launch cuteNTR, either from your window manager or with <code>cutentr</code> in the terminal
-#On your console, open the gift that appeared on your home menu and launch BootNTR Selector
+# On your console, open the gift that appeared on your home menu and launch BootNTR Selector
-#*If you're prompted with 3 buttons on your bottom screen, tap "Use default"
+#* If you're prompted with 3 buttons on your bottom screen, tap "Use default"
-#*If you're prompted to choose an NTR version, choose 3.6
+#* If you're prompted to choose an NTR version, choose 3.6
-#*Your console's screen should flash some colors, meaning that it's ready for streaming
+#* Your console's screen should flash some colors, meaning that it's ready for streaming
-#Input your console's IP from the first section into the IP box next to the <code>Stream</code> button
+# Input your console's IP from the first section into the IP box next to the <code>Stream</code> button
-#Click <code>Stream</code> in the cuteNTR window
+# Click <code>Stream</code> in the cuteNTR window
-#*Your console's screens should now be streamed to your computer
+#* Your console's screens should now be streamed to your computer
 |-|Arch Linux - cuteNTR=
-===What You Need===
+=== What You Need ===
-*Your console's IP from the first section
+* Your console's IP from the first section
-*sudo
+* sudo
-*The latest release of [https://github.com/LumaTeam/Luma3DS/releases/latest Luma3DS]
+* The latest release of {{GitHub|LumaTeam/Luma3DS/releases/latest|Luma3DS}}
-*The latest release of [https://github.com/Nanquitas/BootNTR/releases/latest BootNTR Selector]
+* The latest release of {{GitHub|Nanquitas/BootNTR/releases/latest|BootNTR Selector}}
-*[https://github.com/lifehackerhansol/FBI/releases/latest FBI] installed on your console
+* {{GitHub|lifehackerhansol/FBI/releases/latest|FBI}} installed on your console
 === Section I: Prep Work===
+# Ensure that your console and your computer are on the same network
-#Ensure that your console and your computer are on the same network
 # Download the latest Luma3DS <code>boot.firm</code> file
 # Download the latest BootNTR Selector <code>.cia</code> file
-#Power off your console
+# Power off your console
 # Take the SD card out of your console and put it into your computer
-#Replace the <code>boot.firm</code> file on the root of your SD card with the one you just downloaded
+# Replace the <code>boot.firm</code> file on the root of your SD card with the one you just downloaded
 # Copy the BootNTR selector <code>.cia</code> file to your SD card
-#*You may put this file where you can easily access it
+#* You may put this file where you can easily access it
 # Put your SD card back into your console
 === Section II: Installing cuteNTR===
-This is a small tutorial for installing the popular AUR helper [https://github.com/Jguer/yay yay] and installing cuteNTR with it. If you already have a working AUR helper, or know how to install AUR packages in general, you can download and make <code>cutentr-git</code> yourself, then continue with the next section.
+This is a small tutorial for installing the popular AUR helper {{GitHub|Jguer/yay|yay}} and installing cuteNTR with it. If you already have a working AUR helper, or know how to install AUR packages in general, you can download and make <code>cutentr-git</code> yourself, then continue with the next section.
 # Open the terminal
@@ Line 174: / Line 175: @@
 #* Confirm your password if prompted
-===Section III: Installing CIAs===
+=== Section III: Installing CIAs ===
 # Power on your console
-#*If you are prompted with a Luma3DS configuration screen, just press START
+#* If you are prompted with a Luma3DS configuration screen, just press {{B|START}}
-#Open FBI
+# Open FBI
-# Press A on <code>SD</code> at the top of your bottom screen
+# Press {{B|A}} on <code>SD</code> at the top of your bottom screen
 # Find the BootNTR Selector <code>.cia</code> file that you copied, press A on it and select <code>Install and delete CIA</code>
-#Press START to exit FBI
+# Press {{B|START}} to exit FBI
-===Section IV: Streaming===
+=== Section IV: Streaming ===
 # Launch cuteNTR, either from your window manager or with <code>cutentr</code> in the terminal
-#On your console, open the gift that appeared on your home menu and launch BootNTR Selector
+# On your console, open the gift that appeared on your home menu and launch BootNTR Selector
-#*If you're prompted with 3 buttons on your bottom screen, tap "Use default"
+#* If you're prompted with 3 buttons on your bottom screen, tap "Use default"
-#*If you're prompted to choose an NTR version, choose 3.6
+#* If you're prompted to choose an NTR version, choose 3.6
-#*Your console's screen should flash some colors, meaning that it's ready for streaming
+#* Your console's screen should flash some colors, meaning that it's ready for streaming
-#Input your console's IP from the first section into the IP box next to the <code>Stream</code> button
+# Input your console's IP from the first section into the IP box next to the <code>Stream</code> button
-#Click <code>Stream</code> in the cuteNTR window
+# Click <code>Stream</code> in the cuteNTR window
-#*Your console's screens should now be streamed to your computer
+#* Your console's screens should now be streamed to your computer
 |-|Other Linux - cuteNTR=
-===What You Need===
+=== What You Need ===
-*Your console's IP from the first section
+* Your console's IP from the first section
-*The latest release of [https://flatpak.org/setup/ flatpak] installed on your computer for your operating system
+* The latest release of [https://flatpak.org/setup/ flatpak] installed on your computer for your operating system
-*The latest release of [https://github.com/LumaTeam/Luma3DS/releases/latest Luma3DS]
+* The latest release of {{GitHub|LumaTeam/Luma3DS/releases/latest|Luma3DS}}
-*The latest release of [https://github.com/Nanquitas/BootNTR/releases/latest BootNTR Selector]
+* The latest release of {{GitHub|Nanquitas/BootNTR/releases/latest|BootNTR Selector}}
-*[https://github.com/lifehackerhansol/FBI/releases/latest FBI] installed on your console
+* {{GitHub|lifehackerhansol/FBI/releases/latest|FBI}} installed on your console
-=== Section I: Prep Work===
-#Ensure that your console and your computer are on the same network
+=== Section I: Prep Work ===
+# Ensure that your console and your computer are on the same network
 # Download the latest Luma3DS <code>boot.firm</code> file
 # Download the latest BootNTR Selector <code>.cia</code> file
-#Power off your console
+# Power off your console
 # Take the SD card out of your console and put it into your computer
-#Replace the <code>boot.firm</code> file on the root of your SD card with the one you just downloaded
+# Replace the <code>boot.firm</code> file on the root of your SD card with the one you just downloaded
 # Copy the BootNTR selector <code>.cia</code> file to your SD card
-#*You may put this file where you can easily access it
+#* You may put this file where you can easily access it
 # Put your SD card back into your console
-=== Section II: Installing cuteNTR===
+=== Section II: Installing cuteNTR ===
 # Open the terminal
 # Run <code>mkdir cuteNTR && cd cuteNTR</code> to make a new directory and go into it
@@ Line 221: / Line 220: @@
 # Run <code>cd .. && rm -r cuteNTR</code> to delete the directory
-===Section III: Installing CIAs===
+=== Section III: Installing CIAs ===
 # Power on your console
-#*If you are prompted with a Luma3DS configuration screen, just press START
+#* If you are prompted with a Luma3DS configuration screen, just press {{B|START}}
-#Open FBI
+# Open FBI
-# Press A on <code>SD</code> at the top of your bottom screen
+# Press {{B|A}} on <code>SD</code> at the top of your bottom screen
 # Find the BootNTR Selector <code>.cia</code> file that you copied, press A on it and select <code>Install and delete CIA</code>
-#Press START to exit FBI
+# Press {{B|START}} to exit FBI
-===Section IV: Streaming===
+=== Section IV: Streaming ===
 # Launch cuteNTR by running <code>flatpak run com.gitlab.BoltsJ.cuteNTR</code>
-#On your console, open the gift that appeared on your home menu and launch BootNTR Selector
+# On your console, open the gift that appeared on your home menu and launch BootNTR Selector
-#*If you're prompted with 3 buttons on your bottom screen, tap "Use default"
+#* If you're prompted with 3 buttons on your bottom screen, tap "Use default"
-#*If you're prompted to choose an NTR version, choose 3.6
+#* If you're prompted to choose an NTR version, choose 3.6
-#*Your console's screen should flash some colors, meaning that it's ready for streaming
+#* Your console's screen should flash some colors, meaning that it's ready for streaming
-#Input your console's IP from the first section into the IP box next to the <code>Stream</code> button
+# Input your console's IP from the first section into the IP box next to the <code>Stream</code> button
-#Click <code>Stream</code> in the cuteNTR window
+# Click <code>Stream</code> in the cuteNTR window
-#*Your console's screens should now be streamed to your computer
+#* Your console's screens should now be streamed to your computer
 </tabber>
-==Using Line In to Receive Audio==
+== Using Line In to Receive Audio ==
-===What You Need===
-*A 3.5mm to 3.5mm audio cable
+=== What You Need ===
-*An audio in (line in or microphone in) port on your computer
-**Some computers have a single "headphone" port that can be used for both audio output and input. To use one of these, you will need a Y splitter
-===How to use===
+* A 3.5mm to 3.5mm audio cable
+* An audio in (line in or microphone in) port on your computer
+** Some computers have a single "headphone" port that can be used for both audio output and input. To use one of these, you will need a Y splitter cable
-#Connect your 3DS to your computer's audio input port with a 3.5mm to 3.5mm audio cable
+=== How to use ===
-#Pipe the audio from your audio input port into the software you intend to use
-#*The exact steps will depend on the software you're using
-#*If you are recording or streaming your game using [https://obsproject.com/ OBS], add a new Audio Input Capture
-#*If you are streaming your game via a service such as Discord, you will need to use software such as [https://vb-audio.com/Voicemeeter/ Voicemeeter] to mix your microphone and 3DS audio inputs together
-#**If you do not wish to speak while streaming, simply point the app at the 3DS's audio device
-#**If you do not wish to mix your microphone and 3DS audio inputs together, you can set up a scene using [https://obsproject.com/ OBS], create a Windowed Projector Preview and share on Discord that window. Then, in [https://obsproject.com/kb/audio-mixer-guide#setting-audio-levels Advanced Audio Properties], turn on the Audio Monitoring for the 3DS Audio Input Capture so that viewers on Discord can hear the 3DS audio. Note that this last step will direct the 3DS audio also to your audio output device (headphones/speakers).
-#*To simply listen to the audio, you can [https://www.tenforums.com/tutorials/126383-listen-microphone-through-playback-device-windows.html listen to the audio input device in Windows]
-==Troubleshooting==
+# Connect your 3DS to your computer's audio input port with a 3.5mm to 3.5mm audio cable
+# Pipe the audio from your audio input port into the software you intend to use
+#* The exact steps will depend on the software you're using
+#* If you are recording or streaming your game using [https://obsproject.com/ OBS], add a new Audio Input Capture
+#* If you are streaming your game via a service such as Discord, you will need to use software such as [https://vb-audio.com/Voicemeeter/ Voicemeeter] to mix your microphone and 3DS audio inputs together
+#** If you do not wish to speak while streaming, simply point the app at the 3DS's audio device
+#** If you do not wish to mix your microphone and 3DS audio inputs together, you can set up a scene using [https://obsproject.com/ OBS], create a Windowed Projector Preview and share on Discord that window. Then, in [https://obsproject.com/kb/audio-mixer-guide#setting-audio-levels Advanced Audio Properties], turn on the Audio Monitoring for the 3DS Audio Input Capture so that viewers on Discord can hear the 3DS audio. Note that this last step will direct the 3DS audio also to your audio output device (headphones/speakers).
+#* To simply listen to the audio, you can [https://www.tenforums.com/tutorials/126383-listen-microphone-through-playback-device-windows.html listen to the audio input device in Windows]
-*Games such as those in the Pokemon series, Smash Bros 3DS and many more may crash when trying to load or after a loading screen. To avoid this issue, ensure that the debugger is enabled. To do this see [[3DS:Check local IP address|this]] page.
+== Troubleshooting ==
-*Similarly, such of the above games may disable Wi-Fi connection while using Snickerstream when trying to play online. To counter this, make sure to enable NFC Patch in Snickerstream.
-==Credits==
+* Games such as those in the Pokemon series, Smash Bros 3DS and many more may crash when trying to load or after a loading screen. To avoid this issue, ensure that the debugger is enabled. To do this see [[3DS:Check local IP address|this]] page.
+* Similarly, such of the above games may disable Wi-Fi connection while using Snickerstream when trying to play online. To counter this, make sure to enable NFC Patch in Snickerstream.
 [[Category:Nintendo 3DS guides]]