SD Clean/Linux: Difference between revisions

Revision as of 19:18, 9 April 2023

This is an add-on section for completely recreating an SD card's filesystem using fdisk and mkfs. This should only be done if formatting does not fix your issue or is not possible for some reason.

This page is for Linux users only. If you are not on Linux, see the Windows and/or Mac pages instead.

Instructions

Before beginning these steps, copy all of your SD card's contents to a folder on your computer.

The commands in this guide are case-sensitive. Enter them exactly as written, or there may be unintended consequences.

Make sure your SD card is not inserted.
Open a terminal window and type watch lsblk.

Insert the SD card and watch for a new device appearing in lsblk.

Observe the output for the new device. It should match something like this:

NAME        MAJ:MIN RM   SIZE RO TYPE MOUNTPOINT
mmcblk0     179:0    0   3,8G  0 disk
└─mmcblk0p1 179:1    0   3,7G  0 part /run/media/user/FFFF-FFFF

Take note of the name of the device that now appears. In our example above, it was mmcblk0p1.
- If RO is set to 1, make sure the lock switch is not slid down.
Hit CTRL + C to exit the menu.
For each partition of the disk, type umount /dev/<device name>i.
- Replace i with the partition number you are unmounting.
Type fdisk /dev/<device name>.
Type o, then type n and press ENTER on all prompts.
- If it asks whether to remove a VFAT signature, choose to remove it.
Once you are back at fdisk's main menu, type t and then type 0c.
Type a and then p. Observe the output and make sure the device is now formatted correctly.
If there are no issues, type w. This will save changes and exit the fdisk prompt.
Type sudo mkfs.vfat /dev/(device name) -s 64 to reformat the new partition.
- If the SD card is over 32GB in size, change 64 to 128.
Type sudo eject /dev/(device name), then remove and reinsert the SD card.
Copy your data back onto the SD card.

@@ Line 1: / Line 1: @@
-This is an add-on section for completely recreating an SD card's filesystem using either fdisk and mkfs or GParted. This should only be done if formatting does not fix your issue or is not possible for some reason.
+This is an add-on section for completely recreating an SD card's filesystem using fdisk and mkfs. This should only be done if formatting does not fix your issue or is not possible for some reason.
 This page is for Linux users only. If you are not on Linux, see the [[SD Clean/Windows|Windows]] and/or [[SD Clean/Mac|Mac]] pages instead.
@@ Line 6: / Line 6: @@
 {{warning|Before beginning these steps, copy all of your SD card's contents to a folder on your computer.}}
-=== GParted ===
-# Open GParted.
-#* If you do not have GParted installed, install it using your package manager of choice, such as follows:
-#** Debian-based: <code>sudo apt-get install gparted</code>
-#** Fedora-based: <code>sudo dnf install gparted</code>
-#** Arch-based: <code>sudo pacman -S gparted</code>
-# Find your SD card in the drive list and select it.
-# Open the Device tab and select "Create Partition Table..."
-#* If this fails saying there are active partitions, open the Partition tab and select "Unmount".
-# Select <code>msdos</code> partition type and click "Apply".
-# Right-click on the new "unallocated" space and click "New".
-# Change the filesystem to "fat32", and optionally choose any label that does not start with <code>3ds</code>. Leave all other settings intact.
-# Click "Add", then press the "Apply All Operations" button and click "Apply".
-# Close GParted, then remove and reinsert the SD card.
-# Copy your data back onto the SD card.
-=== Command line ===
 {{warning|The commands in this guide are case-sensitive. Enter them exactly as written, or there may be unintended consequences.}}