Toggle menu
Toggle preferences menu
Toggle personal menu
Not logged in
Your IP address will be publicly visible if you make any edits.

3DS:bmbt3DS

Bare-metal button tester for the 3DS
Revision as of 18:06, 6 September 2024 by ItsCrocoSwine (talk | contribs) (add category)

(diff) ← Older revision | Approved revision (diff) | Latest revision (diff) | Newer revision → (diff)


bmbt3DS is a bare metal button testing .firm payload for the Nintendo 3DS. It can be used to test if all buttons on the console are functioning properly.

Instructions

What You Need

Section I - Running the Test

  1. Power off your console
  2. Remove the SD card from your console and insert it into your computer
  3. Copy bmbt3ds.firm to the root of your SD Card
  4. Rename boot.firm to luma.firm
  5. Rename bmbt3ds.firm to boot.firm
  6. Safely eject the SD card from your computer and reinsert it into your console
  7. Power on the console without pressing any buttons
    Bmbt.png Refer to the attached image for what parts of the screen will light up for each button pressed.
  8. Press each button once, verifying that the corresponding button shows up on the top screen. If it does not show up, the button pressed may be faulty. If you see a constant white square for one button and you are not holding the button down, that button may be stuck and could be the source of some issues.
  9. Once you are finished with the button tester, press the power button once to power off the console
  10. Remove the SD card from your console and insert it into your computer
  11. Delete boot.firm from the root of your SD card
  12. Rename luma.firm to boot.firm
  13. Safely eject the SD card from your computer and reinsert it into your console
  14. Power on your console
Success icon If all went well, you have successfully tested the buttons on your console.

  1. Power off your console
  2. Remove the SD card from your console and insert it into your computer
  3. Copy bmbt3ds.firm to the root of your SD Card
  4. Safely eject the SD card from your computer and reinsert it into your console
  5. Power on the console while holding HOME to enter the fastboot3DS menu
  6. Select [+]Boot from file... -> sdmc: -> bmbt3ds.firm
    Bmbt.png Refer to the attached image for what parts of the screen will light up for each button pressed.
  7. Press each button once, verifying that the corresponding button shows up on the top screen. If it does not show up, the button pressed may be faulty. If you see a constant white square for one button and you are not holding the button down, that button may be stuck and could be the source of some issues.
  8. Once you are finished with the button tester, press the power button once to power off the console
  9. Remove the SD card from your console and insert it into your computer
  10. Delete bmbt3ds.firm from the root of your SD card
  11. Safely eject the SD card from your computer and reinsert it into your console
  12. Power on your console
Success icon If all went well, you have successfully tested the buttons on your console.

Warning icon If you do not have a flashcart compatible with ntrboot, please choose another option.
  1. Power off your console
  2. Remove the SD card from your console and insert it into your computer
  3. Copy bmbt3ds.firm to the root of your SD Card
  4. Rename boot.firm to luma.firm
  5. Rename bmbt3ds.firm to boot.firm
  6. Safely eject the SD card from your computer and reinsert it into your console
  7. Insert the flashcart flashed with ntrboot into your console
  8. Put the magnet into position to trigger the lid sensor. Refer to this image for reference
    • Note, 2DS users will not need a magnet, as their device cannot physically fold. Instead, move the sleep switch to the right
  9. Press and hold START+SELECT+X, then briefly press and hold the power button for 2 to 3 seconds
  10. Your console should now be booted into BMBT.
    • If it did not boot and instead booted into the HOME Menu or turned off immediately, power off your console and try again. You may need a few attempts to get the magnet positioning correct.
    Bmbt.png Refer to the attached image for what parts of the screen will light up for each button pressed.
  11. Press each button once, verifying that the corresponding button shows up on the top screen. If it does not show up, the button pressed may be faulty. If you see a constant white square for one button and you are not holding the button down, that button may be stuck and could be the source of some issues.
  12. Once you are finished with the button tester, press the power button once to power off the console
  13. Remove the SD card from your console and insert it into your computer
  14. Delete boot.firm from the root of your SD card
  15. Rename luma.firm to boot.firm
  16. Safely eject the SD card from your computer and reinsert it into your console
  17. Power on your console
Success icon If all went well, you have successfully tested the buttons on your console.

Warning icon This section only applies to consoles with GodMode9 installed into FIRM0/1.
  1. Power off your console
  2. Remove the SD card from your console and insert it into your computer
  3. Copy bmbt3ds.firm to the sd:/gm9/payloads folder on your SD card
  4. Reinsert the SD card into your console
  5. Power on the console while holding R+ to enter the GodMode9 bootloader menu
  6. Select Select payload... -> bmbt3ds.firm
    Bmbt.png Refer to the attached image for what parts of the screen will light up for each button pressed.
  7. Press each button once, verifying that the corresponding button shows up on the top screen. If it does not show up, the button pressed may be faulty. If you see a constant white square for one button and you are not holding the button down, that button may be stuck and could be the source of some issues.
  8. Once you are finished with the button tester, press the power button once to power off the console
Success icon If all went well, you have successfully tested the buttons on your console.

  1. Power off your console
  2. Remove the SD card from your console and insert it into your computer
  3. Copy bmbt3ds.firm to the sd:/luma/payloads folder on your SD card
  4. Reinsert the SD card into your console
  5. Power on the console while holding START to open Luma3DS chainloader
    • If you dont see Luma3DS chainloader, follow Restoring / Updating CFW and try again
    • If you still don't see it, follow the boot9strap tab above instead
  6. Select bmbt3ds.firm
    Bmbt.png Refer to the attached image for what parts of the screen will light up for each button pressed.
  7. Press each button once, verifying that the corresponding button shows up on the top screen. If it does not show up, the button pressed may be faulty. If you see a constant white square for one button and you are not holding the button down, that button may be stuck and could be the source of some issues.
  8. Once you are finished with the button tester, press the power button once to power off the console
Success icon If all went well, you have successfully tested the buttons on your console.