3DS:Splash screens

Splash screens are images that can be displayed on the top and bottom screen during startup. You could use these images to, for example:

Remind you of key combinations (e.g. hold SELECT for Luma3DS configuration, hold START for Luma3DS chainloader)
Display a commemorative BIOS screen

Splash screens are static images. If you want to see an animation on boot-up instead, check out 3DS:Boot animations.

TODO:

fastboot3DS splash screens
Anemone3DS instructions

Splash screens do not display during the boot process, they interrupt it. For instance, if you have a splash screen that last three seconds, your boot time will be increased by three seconds.

Enabling splash screens

In order for splash screens to be displayed, they must be enabled from Luma3DS configuration. You'll only need to do this once (unless your configuration file is reset).

If you have a PIN enabled, the splash screen will be displayed after you enter your PIN.

Power off your device
Press and hold (Select), and while holding (Select), power on your device to enter the Luma3DS configuration menu
Scroll down to Splash and press (A) until you see (x) to the right of Before
- You could also set it to After, but that would make payloads inaccessible from the splash screen which would lessen the usefulness of the splash screen

By default, the splash screen will last 3000 milliseconds (3 seconds). If you wish to extend or shorten this time, modify the splash_duration_ms line in the file config.ini (inside the luma folder).

Downloading/installing a splash screen

Using Anemone3DS

Open the Anemone3DS application
Press the letter "T" on the top right-hand corner to switch to Splash mode
If you don't already have a splash, press (Right Shoulder) to open the QR scanner
- You can scan the QR code of a theme you like from here
Press (A) to install whatever splash is highlighted

Your splash has been successfully applied!

Manually

Put your SD card into your computer
Get your splash screen of choice. You can get one you like from here
Open the .zip file that the splash screen is inside of
Extract splash.bin and splashbottom.bin to the luma folder on your SD card
Put your SD card back into your 3DS

Your splash has been successfully applied!

Splash screens on CTRNAND

This may be useful in cases where you want to:

Indicate that the SD card has been removed
Indicate your address or contact details should your device be stolen

Enabling splash screens on CTRNAND

You'll only need to do this once (unless your configuration file is reset).

Remove your SD card from your 3DS
Press and hold (Select), and while holding (Select), power on your device to enter the Luma3DS (CTRNAND) configuration menu
Scroll down to Splash and press (A) until you see (x) to the right of Before
- You could also set it to After, but that would make payloads inaccessible from the splash screen which would lessen the usefulness of the splash screen

Applying splash screens on CTRNAND

Put your SD card into your computer
Get your splash screen of choice. You can get one you like from here
Open the .zip file that the splash screen is inside of
Extract splash.bin and splashbottom.bin to anywhere on your SD card
Put your SD card back into your 3DS
Press and hold (Start), and while holding (Start), power on your device to enter GodMode9 (or the Luma3DS chainloader)
Navigate to [0:] SDCARD -> <wherever you put your splash screens
Press (Left Shoulder) to mark both splash.bin and splashbottom.bin
Press (Y) to copy the items
Press (B) until you are back at the GodMode9 [root] screen
Navigate to [1: SYSNAND CTRNAND] -> rw -> luma
Press (Y) to paste the items
Press (A) to unlock SysNAND (lvl1) writing, then input the key combo given
Press (A) to continue
Press (Home) to bring up the action menu
Select “Poweroff system” to power off your device

Your splash has been successfully applied to CTRNAND!

Splash screens with fastboot3DS

fastboot3DS is also capable of using splash screens if you want to have two splash screens for some reason (or don't want to use Luma3DS's splash screen feature). You can use the same splash screen images that you'd use for Luma3DS.

On boot, while the splash is displayed, you will be able to hold the (Home) button to enter fastboot3DS's menu.

Hold the (Home) button, then power on your device while still holding (Home) to enter fastboot3DS's menu
Navigate to Boot setup... -> Change boot mode...
Ensure that "Set quick boot" is enabled
Press (B) to go back, then navigate to Change splash...


Select Use custom splash...
Navigate to the folder where your splashes (splash.bin and splashbottom.bin) are located, then press (X) while hovering over the folder
For example, if your splashes are in luma, then hover over luma (do not enter the folder) and press (X).
Wait for fastboot3DS to convert the splash



 
Your splash has been successfully applied!

If you want to change the duration of your splash:

Hold the (Home) button, then power on your device while still holding (Home) to enter fastboot3DS's menu
Navigate to Boot setup... -> Change splash... -> Set splash duration...
Use the D-Pad Up and Down keys to select how long you want your splash to display, then press (A) to confirm
There is a minimum and maximum time of 500ms and 10,000ms (0.5 to 10 seconds), respectively

Creating a splash screen

If you want to put your graphic designer passion into use, you can create your own splash screen. This process can be generally simplified with the splash-ds web tool, but the gist is:

Create your images with an image editor of your choice
You probably want to use JPG files since the 3DS probably isn't going to handle transparency very well
The top screen must be 400x240 px and the bottom screen must be 320x240 px
Open the splash-ds website
Drag-and-drop your images into the website, and play with the settings as you see fit
Click "Download splash screen"
Open the resulting .zip file that the splash screen is inside of
Put your SD card into your computer
Extract splash.bin and splashbottom.bin to the luma folder on your SD card
Put your SD card back into your 3DS



 
Your custom splash screen has been successfully applied!