This is an add-on section for formatting an SD card to FAT32.
This page is for Linux users only. If you are not on Linux, check out the Windows or Mac pages.
Instructions
Before beginning these steps, copy all of your SD card's contents to a folder on your computer.
The commands in this guide are case-sensitive. Enter them exactly as written, or there may be unintended consequences.
Make sure your SD card is not inserted
Open a terminal window and type watch lsblk
Insert the SD card and watch for a new device appearing in lsblk
Observe the output for the new device. It should match something like this:
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
mmcblk0 179:0 0 3,8G 0 disk
└─mmcblk0p1 179:1 0 3,7G 0 part /run/media/user/FFFF-FFFF
Take note of the name of the device that now appears. In our example above, it was mmcblk0p1, but it could show up as sda or sdb, if you use a USB adapter
If RO is set to 1, make sure the lock switch is not slid down
Hit CTRL + C to exit the menu
Install the fdisk and dosfstools packages using your package manager of choice
Type sudo fdisk /dev/<device name>
Enter t and then enter 0c
Enter a and then p - observe the output, and make sure the device is now formatted correctly
If there are no issues, enter w - this will save changes and exit the fdisk prompt
Type sudo mkfs.vfat /dev/<device name>1 -s 64 to reformat the new partition
If the SD card is over 32GB in size, change 64 to 128
Type sudo eject /dev/<device name>, then remove and reinsert the SD card
Copy your data back onto the SD card
Make sure your SD card is not inserted
Open a terminal window and type watch lsblk
Insert the SD card and watch for a new device appearing in lsblk
Observe the output for the new device. It should match something like this:
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
mmcblk0 179:0 0 3,8G 0 disk
└─mmcblk0p1 179:1 0 3,7G 0 part /run/media/user/FFFF-FFFF
Take note of the name of the device that now appears. In our example above, it was mmcblk0p1, but it could show up as sda or sdb, if you use a USB adapter
If RO is set to 1, make sure the lock switch is not slid down
Hit CTRL + C to exit the menu
Install the cfdisk and dosfstools packages using your package manager of choice
Type sudo cfdisk /dev/<device name>
Choose the Delete option and delete any existing partitions
Choose the New option, keep partition size at the recommended size, and choose primary partition type
Choose the Type option, scroll up until you see b W95 FAT32 and select it
Finally, choose the Write option. This will overwrite any existing data. You have been warned.
Choose the Quit option
Type sudo eject /dev/<device name>, then remove and reinsert the SD card
Copy your data back onto the SD card
Make sure your SD card is not inserted
Open a terminal window and type watch lsblk
Insert the SD card and watch for a new device appearing in lsblk
Observe the output for the new device. It should match something like this:
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
mmcblk0 179:0 0 3,8G 0 disk
└─mmcblk0p1 179:1 0 3,7G 0 part /run/media/user/FFFF-FFFF
Take note of the name of the device that now appears. In our example above, it was mmcblk0p1, but it could show up as sda or sdb, if you use a USB adapter
If RO is set to 1, make sure the lock switch is not slid down
Hit CTRL + C to exit the menu
Install the parted and dosfstools packages using your package manager of choice
Type sudo parted /dev/<device name> mklabel msdos
Type sudo parted -a opt /dev/<device name> mkpart primary fat32 0% 100%
Type sudo eject /dev/<device name>, then remove and reinsert the SD card.
Copy your data back onto the SD card.
Make sure your SD card is not inserted
Open a terminal window and type watch lsblk.
Insert the SD card and watch for a new device appearing in lsblk.
Observe the output for the new device. It should match something like this:
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
mmcblk0 179:0 0 3,8G 0 disk
└─mmcblk0p1 179:1 0 3,7G 0 part /run/media/user/FFFF-FFFF
Take note of the name of the device that now appears. In our example above, it was mmcblk0p1
If RO is set to 1, make sure the lock switch is not slid down
Hit CTRL + C to exit the menu
Type sudo fdisk /dev/<device name>
Enter t and then enter 0c
Enter a and then p - observe the output, and make sure the device is now formatted correctly.
If there are no issues, enter w - this will save changes and exit the fdisk prompt.
Type sudo mkfs.vfat /dev/<device name>1 -s 64 to reformat the new partition.
If the SD card is over 32GB in size, change 64 to 128
Type sudo eject /dev/<device name>, then remove and reinsert the SD card.
