|
|
| (12 intermediate revisions by 5 users not shown) |
| Line 1: |
Line 1: |
| {{Page WIP|notes=
| | This is an add-on section for formatting an SD card to FAT32. |
| *This page needs to actually do repartitioning properly, or else on certain SD cards that come with exFAT, the partition table won't be updated to reflect this. Maybe use fdisk for this?
| |
| *GUI options for people who can use that such as GNOME Disks or GParted (which can be installed with most package managers).
| |
| }}
| |
|
| |
|
| This is an add-on section for formatting an SD card to work with the 3DS. | | This page is for Linux users only. If you are not on Linux, check out the [[Special:MyLanguage/Formatting an SD card/Windows|Windows]] or [[Special:MyLanguage/Formatting an SD card/Mac|Mac]] pages. |
| | |
| | == Instructions == |
| | {{warning|Before beginning these steps, copy all of your SD card's contents to a folder on your computer.}} |
| | |
| | {{warning|The commands in this guide are case-sensitive. Enter them exactly as written, or there may be unintended consequences.}} |
| | <tabber> |
| | |-|fdisk= |
|
| |
|
| If the 3DS already recognizes the SD card, this guide is not required. | | <span> |
| | # Make sure your SD card is '''not''' inserted |
| | # Open a terminal window and type <code>watch lsblk</code> |
| | # Insert the SD card and watch for a new device appearing in lsblk |
| | # Observe the output for the new device. It should match something like this: {{#tag:syntaxhighlight| |
| | NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT |
| | mmcblk0 179:0 0 29.7G 0 disk |
| | └─mmcblk0p1 179:1 0 29.5G 0 part /run/media/user/FFFF-FFFF |
| | |lang=text}} |
| | # Take note of the name of the device that now appears. In our example above, it was <code>mmcblk0</code>, but it could show up as <code>sda</code> or <code>sdb</code>, if you use a USB adapter |
| | #* If <code>RO</code> is set to 1, make sure the lock switch is not slid down |
| | # Hit CTRL + C to exit the menu |
| | # Type <code>sudo umount /dev/<device name>*</code> (do not replace the <code>*</code>) |
| | # Install the <code>fdisk</code> and <code>dosfstools</code> packages using your package manager of choice |
| | # Type <code>sudo fdisk /dev/<device name></code> |
| | # Enter <code>o</code>, this will create a new MBR partition scheme |
| | # Enter <code>n</code>, then press enter until you're returned to the prompt |
| | #* The default values will work fine for all consoles |
| | # Enter <code>t</code>, then enter <code>0c</code> |
| | # Enter <code>a</code> and then <code>p</code> - observe the output, and make sure the device is now formatted correctly: {{#tag:syntaxhighlight| |
| | Disk /dev/mmcblk0: 29.72 GiB, 31914983424 bytes, 62333952 sectors |
| | Units: sectors of 1 * 512 = 512 bytes |
| | Sector size (logical/physical): 512 bytes / 512 bytes |
| | I/O size (minimum/optimal): 512 bytes / 512 bytes |
| | Disklabel type: dos |
| | Disk identifier: 0x######## |
| | |
| | Device Boot Start End Sectors Size Id Type |
| | /dev/<partition name> 8192 62333951 62325760 29.7G c W95 FAT32 (LBA) |
| | |lang=text}} |
| | # If there are no issues, enter <code>w</code> - this will save changes and exit the fdisk prompt |
| | # Type <code>sudo mkfs.vfat /dev/<partition name> -s 64</code> to reformat the new partition |
| | #* If the SD card is over 32GB in size, change <code>64</code> to <code>128</code> |
| | # Type <code>sudo eject /dev/<device name></code>, then remove and reinsert the SD card |
| | # Copy your data back onto the SD card |
| | </span> |
|
| |
|
| This page is for Linux users only. If you are not on Linux, check out the [[Special:MyLanguage/Formatting an SD card/Windows|Windows]] or [[Special:MyLanguage/Formatting an SD card/Mac|Mac]] pages.
| |
|
| |
|
| == Instructions ==
| | |-|parted= |
|
| |
|
| | <span> |
| # Make sure your SD card is '''not''' inserted | | # Make sure your SD card is '''not''' inserted |
| # Launch the Linux Terminal | | # Open a terminal window and type <code>watch lsblk</code> |
| # Type <code>watch "lsblk"</code>
| | # Insert the SD card and watch for a new device appearing in lsblk |
| # Insert your SD card into your PC | | # Observe the output for the new device. It should match something like this: {{#tag:syntaxhighlight| |
| # Observe the output. It should match something like this: {{#tag:syntaxhighlight| | | NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT |
| NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT | | mmcblk0 179:0 0 29.7G 0 disk |
| mmcblk0 179:0 0 3,8G 0 disk | | └─mmcblk0p1 179:1 0 29.5G 0 part /run/media/user/FFFF-FFFF |
| └─mmcblk0p1 179:1 0 3,7G 0 part /run/media/user/FFFF-FFFF | |
| |lang=text}} | | |lang=text}} |
| # Take note of the device name. In our example above, it was <code>mmcblk0p1</code> | | # Take note of the name of the device that now appears. In our example above, it was <code>mmcblk0</code>, but it could show up as <code>sda</code> or <code>sdb</code>, if you use a USB adapter |
| #* If <code>RO</code> is set to 1, make sure the lock switch is not slid down | | #* If <code>RO</code> is set to 1, make sure the lock switch is not slid down |
| # Hit CTRL + C to exit the menu | | # Hit CTRL + C to exit the menu |
| # Type in the following for your SD card: | | # Install the <code>parted</code> and <code>dosfstools</code> packages using your package manager of choice |
| #* 2GB or lower: <code>sudo mkfs.fat /dev/(device name from above) -s 64 -F 16</code> | | # Type <code>sudo parted /dev/<device name> mklabel msdos</code> |
| #** This creates a single FAT16 partition with 32 KB cluster size on the SD card | | # Type <code>sudo parted -a opt /dev/<device name> mkpart primary fat32 0% 100%</code> |
| #* 4GB - 128GB: <code>sudo mkfs.fat /dev/(device name from above) -s 64 -F 32</code> | | # Type <code>sudo mkfs.vfat /dev/<partition name> -s 64</code> to reformat the new partition |
| #** This creates a single FAT32 partition with 32 KB cluster size on the SD card | | #* If the SD card is over 32GB in size, change <code>64</code> to <code>128</code> |
| #* 128GB or higher: <code>sudo mkfs.fat /dev/(device name from above) -s 128 -F 32</code> | | # Type <code>sudo eject /dev/<device name></code>, then remove and reinsert the SD card |
| #** This creates a single FAT32 partition with 64 KB cluster size on the SD card | | # Copy your data back onto the SD card |
| | </span> |
|
| |
|
| | |
| | |-|KDE Partition Manager= |
| | |
| | <span> |
| | # Make sure your SD card is '''not''' inserted |
| | # Open KDE Partition Manager, inputting your password as needed |
| | # Insert your SD card and click <code>Refresh Devices</code>. The new device that shows up in the left pane is your SD card |
| | # Click your SD card, then click the <code>New Partition Table</code> button at the top of the window |
| | # When asked, choose <code>Ms-Dos</code>. Do '''NOT''' use <code>GPT</code> |
| | #* [[File:KDE Partition Manager - MBR.png]] |
| | # Right click the <code>unallocted</code> space in the right pane and select <code>New</code> |
| | # When selecting your filesystem, choose <code>FAT32</code> from the drop-down menu. The window should look like this: |
| | #* [[File:KDE Partition Manager - New Partition.png]] |
| | # Click <code>OK</code>, then click <code>Apply</code>, then <code>Apply Pending Operations</code> |
| | # Eject and reinsert your SD card |
| | # Copy your data back onto the SD card |
| | </tabber> |
| {{hg imported|Guide_3DS}} | | {{hg imported|Guide_3DS}} |
|
| |
|
| [[Category:General guides]] | | [[Category:General guides]] |
