Formatting an SD card/Linux: Difference between revisions

Revision as of 02:44, 19 November 2023

This is an add-on section for formatting an SD card to FAT32.

This page is for Linux users only. If you are not on Linux, check out the Windows or Mac pages.

Instructions

Before beginning these steps, copy all of your SD card's contents to a folder on your computer.

The commands in this guide are case-sensitive. Enter them exactly as written, or there may be unintended consequences.

Make sure your SD card is not inserted
Open a terminal window and type watch lsblk
Insert the SD card and watch for a new device appearing in lsblk

Observe the output for the new device. It should match something like this:

NAME        MAJ:MIN RM   SIZE RO TYPE MOUNTPOINT
mmcblk0     179:0    0   3,8G  0 disk
└─mmcblk0p1 179:1    0   3,7G  0 part /run/media/user/FFFF-FFFF

Take note of the name of the device that now appears. In our example above, it was mmcblk0p1, but it could show up as sda or sdb, if you use a USB adapter
- If RO is set to 1, make sure the lock switch is not slid down
Hit CTRL + C to exit the menu
Install the fdisk and dosfstools packages using your package manager of choice
Type sudo fdisk /dev/<device name>
Enter t and then enter 0c
Enter a and then p - observe the output, and make sure the device is now formatted correctly
If there are no issues, enter w - this will save changes and exit the fdisk prompt
Type sudo mkfs.vfat /dev/<device name>1 -s 64 to reformat the new partition
- If the SD card is over 32GB in size, change 64 to 128
Type sudo eject /dev/<device name>, then remove and reinsert the SD card
Copy your data back onto the SD card

Make sure your SD card is not inserted
Open a terminal window and type watch lsblk
Insert the SD card and watch for a new device appearing in lsblk

Observe the output for the new device. It should match something like this:

NAME        MAJ:MIN RM   SIZE RO TYPE MOUNTPOINT
mmcblk0     179:0    0   3,8G  0 disk
└─mmcblk0p1 179:1    0   3,7G  0 part /run/media/user/FFFF-FFFF

Take note of the name of the device that now appears. In our example above, it was mmcblk0p1, but it could show up as sda or sdb, if you use a USB adapter
- If RO is set to 1, make sure the lock switch is not slid down
Hit CTRL + C to exit the menu
Install the cfdisk and dosfstools packages using your package manager of choice
Type sudo cfdisk /dev/<device name>
Choose the Delete option and delete any existing partitions
Choose the New option, keep partition size at the recommended size, and choose primary partition type
Choose the Type option, scroll up until you see b W95 FAT32 and select it
Finally, choose the Write option.
Choose the Quit option
Type sudo eject /dev/<device name>, then remove and reinsert the SD card
Copy your data back onto the SD card

Make sure your SD card is not inserted
Open a terminal window and type watch lsblk
Insert the SD card and watch for a new device appearing in lsblk

Observe the output for the new device. It should match something like this:

NAME        MAJ:MIN RM   SIZE RO TYPE MOUNTPOINT
mmcblk0     179:0    0   3,8G  0 disk
└─mmcblk0p1 179:1    0   3,7G  0 part /run/media/user/FFFF-FFFF

Take note of the name of the device that now appears. In our example above, it was mmcblk0p1, but it could show up as sda or sdb, if you use a USB adapter
- If RO is set to 1, make sure the lock switch is not slid down
Hit CTRL + C to exit the menu
Install the parted and dosfstools packages using your package manager of choice
Type sudo parted /dev/<device name> mklabel msdos
Type sudo parted -a opt /dev/<device name> mkpart primary fat32 0% 100%
Type sudo eject /dev/<device name>, then remove and reinsert the SD card.
Copy your data back onto the SD card.

@@ Line 15: / Line 15: @@
 # Insert the SD card and watch for a new device appearing in lsblk
 # Observe the output for the new device. It should match something like this: {{#tag:syntaxhighlight|
-NAME        MAJ:MIN RM  SIZE RO TYPE MOUNTPOINT
+NAME        MAJ:MIN RM   SIZE RO TYPE MOUNTPOINT
-mmcblk0     179:0    0 29.7G  0 disk
+mmcblk0     179:0    0   3,8G  0 disk
-└─mmcblk0p1 179:1    0 29.5G  0 part /run/media/user/FFFF-FFFF
+└─mmcblk0p1 179:1    0   3,7G  0 part /run/media/user/FFFF-FFFF
 |lang=text}}
-# Take note of the name of the device that now appears. In our example above, it was <code>mmcblk0</code>, but it could show up as <code>sda</code> or <code>sdb</code>, if you use a USB adapter
+# Take note of the name of the device that now appears. In our example above, it was <code>mmcblk0p1</code>, but it could show up as <code>sda</code> or <code>sdb</code>, if you use a USB adapter
 #* If <code>RO</code> is set to 1, make sure the lock switch is not slid down
 # Hit CTRL + C to exit the menu
-# Type <code>sudo umount /dev/<device name>*</code> (do not replace the <code>*</code>)
 # Install the <code>fdisk</code> and <code>dosfstools</code> packages using your package manager of choice
 # Type <code>sudo fdisk /dev/<device name></code>
-# Enter <code>o</code>, this will create a new MBR partition scheme
+# Enter <code>t</code> and then enter <code>0c</code>
-# Enter <code>n</code>, then press enter until you're returned to the prompt
+# Enter <code>a</code> and then <code>p</code> - observe the output, and make sure the device is now formatted correctly
-#* The default values will work fine for all consoles
-# Enter <code>t</code>, then enter <code>0c</code>
-# Enter <code>a</code> and then <code>p</code> - observe the output, and make sure the device is now formatted correctly: {{#tag:syntaxhighlight|
-Disk /dev/mmcblk0: 29.72 GiB, 31914983424 bytes, 62333952 sectors
-Units: sectors of 1 * 512 = 512 bytes
-Sector size (logical/physical): 512 bytes / 512 bytes
-I/O size (minimum/optimal): 512 bytes / 512 bytes
-Disklabel type: dos
-Disk identifier: 0x########
-Device                Boot  Start      End  Sectors  Size Id Type
-/dev/<partition name>        8192 62333951 62325760 29.7G  c W95 FAT32 (LBA)
-|lang=text}}
 # If there are no issues, enter <code>w</code> - this will save changes and exit the fdisk prompt
-# Type <code>sudo mkfs.vfat /dev/<partition name> -s 64</code> to reformat the new partition
+# Type <code>sudo mkfs.vfat /dev/<device name>1 -s 64</code> to reformat the new partition
 #* If the SD card is over 32GB in size, change <code>64</code> to <code>128</code>
 # Type <code>sudo eject /dev/<device name></code>, then remove and reinsert the SD card
@@ Line 47: / Line 33: @@
 </span>
+|-|cfdisk=
-|-|parted=
 <span>
@@ Line 55: / Line 40: @@
 # Insert the SD card and watch for a new device appearing in lsblk
 # Observe the output for the new device. It should match something like this: {{#tag:syntaxhighlight|
-NAME        MAJ:MIN RM  SIZE RO TYPE MOUNTPOINT
+NAME        MAJ:MIN RM   SIZE RO TYPE MOUNTPOINT
-mmcblk0     179:0    0 29.7G  0 disk
+mmcblk0     179:0    0   3,8G  0 disk
-└─mmcblk0p1 179:1    0 29.5G  0 part /run/media/user/FFFF-FFFF
+└─mmcblk0p1 179:1    0   3,7G  0 part /run/media/user/FFFF-FFFF
 |lang=text}}
-# Take note of the name of the device that now appears. In our example above, it was <code>mmcblk0</code>, but it could show up as <code>sda</code> or <code>sdb</code>, if you use a USB adapter
+# Take note of the name of the device that now appears. In our example above, it was <code>mmcblk0p1</code>, but it could show up as <code>sda</code> or <code>sdb</code>, if you use a USB adapter
 #* If <code>RO</code> is set to 1, make sure the lock switch is not slid down
 # Hit CTRL + C to exit the menu
-# Install the <code>parted</code> and <code>dosfstools</code> packages using your package manager of choice
+# Install the <code>cfdisk</code> and <code>dosfstools</code> packages using your package manager of choice
-# Type <code>sudo parted /dev/<device name> mklabel msdos</code>
+# Type <code>sudo cfdisk /dev/<device name></code>
-# Type <code>sudo parted -a opt /dev/<device name> mkpart primary fat32 0% 100%</code>
+# Choose the <code>Delete</code> option and delete any existing partitions
-# Type <code>sudo mkfs.vfat /dev/<partition name> -s 64</code> to reformat the new partition
+# Choose the <code>New</code> option, keep partition size at the recommended size, and choose primary partition type
-#* If the SD card is over 32GB in size, change <code>64</code> to <code>128</code>
+# Choose the <code>Type</code> option, scroll up until you see <code>b W95 FAT32</code> and select it
+# Finally, choose the <code>Write</code> option.
+# Choose the <code>Quit</code> option
 # Type <code>sudo eject /dev/<device name></code>, then remove and reinsert the SD card
 # Copy your data back onto the SD card
 </span>
+|-|parted=
-|-|KDE Partition Manager=
 <span>
 # Make sure your SD card is '''not''' inserted
-# Open KDE Partition Manager, inputting your password as needed
+# Open a terminal window and type <code>watch lsblk</code>
-# Insert your SD card and click <code>Refresh Devices</code>. The new device that shows up in the left pane is your SD card
+# Insert the SD card and watch for a new device appearing in lsblk
-# Click your SD card, then click the <code>New Partition Table</code> button at the top of the window
+# Observe the output for the new device. It should match something like this: {{#tag:syntaxhighlight|
-# When asked, choose <code>Ms-Dos</code>. Do '''NOT''' use <code>GPT</code>
+NAME        MAJ:MIN RM   SIZE RO TYPE MOUNTPOINT
-#* [[File:KDE Partition Manager - MBR.png]]
+mmcblk0     179:0    0   3,8G  0 disk
-# Right click the <code>unallocted</code> space in the right pane and select <code>New</code>
+└─mmcblk0p1 179:1    0   3,7G  0 part /run/media/user/FFFF-FFFF
-# When selecting your filesystem, choose <code>FAT32</code> from the drop-down menu. The window should look like this:
+|lang=text}}
-#* [[File:KDE Partition Manager - New Partition.png]]
+# Take note of the name of the device that now appears. In our example above, it was <code>mmcblk0p1</code>, but it could show up as <code>sda</code> or <code>sdb</code>, if you use a USB adapter
-# Click <code>OK</code>, then click <code>Apply</code>, then <code>Apply Pending Operations</code>
+#* If <code>RO</code> is set to 1, make sure the lock switch is not slid down
-# Eject and reinsert your SD card
+# Hit CTRL + C to exit the menu
-# Copy your data back onto the SD card
+# Install the <code>parted</code> and <code>dosfstools</code> packages using your package manager of choice
+# Type <code>sudo parted /dev/<device name> mklabel msdos</code>
+# Type <code>sudo parted -a opt /dev/<device name> mkpart primary fat32 0% 100%</code>
+# Type <code>sudo eject /dev/<device name></code>, then remove and reinsert the SD card.
+# Copy your data back onto the SD card.
+</span>
 </tabber>
 {{hg imported|Guide_3DS}}
 [[Category:General guides]]